ALPHA, SUOMY의 새로운 크로스 파이버 헬멧, 최종 사용자를위한 내부 편안함, 기술 및 안전에 대한 세부 사항에 공부.
TRICARBOCO 소재의 쉘은 두 가지 크기 (M 및 L), 케블라, 탄소 및 섬유 조인트의 패브릭 혼합으로 생산됩니다.
3 가지 크기 (S, M 및 L)의 내부 폴리스티렌은 가변 밀도로 최상의 편안함을 제공합니다.
호모로게이션 ECE 22-05
내부 폴리스티렌은 최상의 피팅을 얻기 위해 3 가지 크기로 생산되었습니다. 이러한 특성은 충격에 의해 생성된 에너지의 점진적이고 점진적인 흡수를 허용한다.
충격에 의해 생성 된 에너지의 큰 부분이 외부 쉘에 의해 흡수되더라도, 그 변형 덕분에, 폴리스티렌의 역할은 잔류 에너지의 흡수를 위한 결정이다.
폴리스티렌의 다양한 밀도는 우리가 쉘 / 폴리스티렌의 기계적 성능을 최적화 할 수 있습니다.
D-링 리텐션 시스템은 Suomy가 설계하고 특허를 받았습니다. 스트랩의 자유 면을 링에 삽입합니다. 스트랩이 턱에 단단히 누를 때까지 끝을 당깁니다.
이 작업 후에는 헬멧을 제거할 수 없습니다. 뒤에서 잡고 앞쪽으로 회전하여 제거 할 수 없으며 머리에 고정되어 있는지 확인하십시오.
헬멧이 벗겨지거나 자유롭게 회전하는 경향이 있는 경우, 올바른 압력이 얻어지고 테스트를 반복할 때까지 스트랩을 다시 조입니다. 테스트를 반복한 후 고정 시스템을 효율적으로 조일 수 없는 경우 헬멧을 사용하지 마십시오.
스트랩의 올바른 장력을 확인한 후에만 자동 스터드로 잠그는 자유 끝을 이형 탭에 고정하면 자동 스터드가 스트랩의 자유 끝을 고정하여 라이딩 중 플래핑을 방지할 수 있습니다. 이형 버튼을 고정한다고 해서 헬멧이 올바른 위치에 있고 제대로 고정되었는지 는 보장하지 않습니다: 스트랩의 올바른 잠금은 위의 단락에 따라 독점적으로 확인해야 합니다.
고정 시스템을 해제하려면 자동 스터드 버튼을 해제하고 릴리즈 탭을 당겨 잠금을 풀습니다. «D 링»에서 스트랩의 자유 끝을 밀어 내십시오.
릴리스 탭을 사용하여 헬멧을 제거하십시오! 라이딩 하는 동안이 탭을 해제 하지 마십시오.
내부 폴리스티렌은 쉘에 넣어, 공기 환기를 wityh 함께 작동하기 위해 연구되었다. 이 채널은 완벽한 내부 공기 흐름을 허용하고 동시에 백 환기에서 빠른 외부 공기 흐름을 허용합니다.
추가 제품 정보
자물쇠
더블D
원 영문 설명
ALPHA, new cross fiber helmet of SUOMY , studied in details for internal comfort, technologies, and safety for end user.
Shell in TRICARBOCO material, produced in two sizes (M and L), fabric mix of Kevlar, carbon and fiber joint by resin.
Internal polystyrene in 3 sizes (S , M and L) to get the best comfort with variable density.
Homologations ECE 22-05
The INTERNAL POLYSTYRENE produced in 3 sizes to get the best fitting. This characteristic allows a gradual and progressive absorption of the energy produced by the impact.
Even if the bigger part of the energy created by the impact is absorbed by the external shell, thanks to its deformation, the role of polystyrene is determinant for the absorption of the residual energy.
A diversified density of the polystyrene, permit us to optimize the mechanical performance of the shell/polystyrene.
The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw.
After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head.
If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet.
Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs.
To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings».
Use the release tab only to remove the helmet! Never release this tab while riding.
The internal polystyrene has been studied to work together wityh the air ventilations, put on the shell. The channels allow the perfect inside air flow and at the same time a quick outside air flow from back ventilation.
평가 (1)
Suomy Alpha 모토크로스 헬멧 화이트 에 대한 고객 평가
평가 수: 1
평균 평점: 5
1 Español전부
EXCELENTE(10.05.2018)
Anonymous134331703
DE MUY BUENA CALIDAD, MUY COMODO Y MUY LIGERO. LO COMPRE BLANCO; PORQUE LO VOY A ROTULAR,
치수 표
A. 적절한 헬멧 사이즈를 결정하기 위해, 측정 밴드로 머리둘레가 가장 큰 지점(귀 위 약 1cm)을 측정합니다.
표에서 찾은 사이즈를 선택합니다