타의 추종을 불허하는 온보드 샷을 위한 보다 안정적이고 신뢰할 수 있는 디자인. Insta360 Action Invisible Selfie Stick과 함께 사용하면 진정한 블록버스터급 잠재력의 놀라운 3인칭 사진을 잠금 해제할 수 있습니다.
기능:
특허받은 새로운 짐벌 구조로 새로워진 디자인은 오토바이 촬영에 전례 없는 안정성을 제공합니다.
완전히 새로워진 디자인으로 보다 안정적인 3인칭 촬영이 가능합니다.
대부분의 주류 오토바이에 적용할 수 있습니다.
표준 1/4" 어댑터 디자인은 Insta360 Action Invisible Selfie Stick을 지원합니다.
GO 2는 액션 마운트 어댑터와 함께 조립해야 합니다.
사양:
무게: 201g
크기: 96.5x51.5x57mm
호환 가능:
에이스 프로, 에이스, X3, ONE RS(트윈/4K), GO 2, ONE X2, ONE R, ONE X
노트:
클램핑 위치와 크기에 따라 U-볼트 내부에 스페이서를 설치합니다.
사용하기 전에 범용 조인트를 U-볼트에 단단히 조이십시오.
포함된 와셔 쌍은 두 개의 와셔 세트로 구성됩니다. 와셔를 잃어버리면 진동으로 인해 너트가 느슨해질 수 있으므로 분해하는 동안 분실하지 않도록 주의하십시오.
U-볼트는 오토바이 프레임, 리어 페달 브래킷, 범퍼 및 기타 안전한 영역에 설치할 수 있습니다. U-볼트가 고정되었을 때 마운트에서 회전하거나 유격하지 않고 제자리에 고정되어 있는지 항상 확인하십시오.
80km/h(50mph)를 초과하지 않는 속도의 부드러운 도로에서만 라이딩하는 것이 좋습니다. 오프로드 라이딩은 지원되지 않습니다.
Insta360 Action Invisible Selfie Stick을 Universal 조인트의 1/4" 어댑터와 연결하여 스틱이 단단히 장착되었는지 확인하는 것이 좋습니다. 셀카봉을 나머지 액세서리에 연결하지 마세요. 과도한 토크는 유니버셜 조인트를 손상시킬 수 있으므로 셀카봉 상단을 세게 비틀지 마십시오.
오토바이를 장기간 외부에 주차할 경우 액세서리를 제거하여 최상의 상태로 유지하십시오.
이 사용 설명서의 설치 방법에 따라 액세서리를 사용하고 DIY하지 마십시오. 지침을 따르지 않아 발생한 손상은 Insta360 보증 또는 교체 서비스가 적용되지 않습니다.
목차:
1x 유니버셜 조인트
1x U-볼트
1x 렌치
1x 육각 렌치
1x 대형 스페이서
1x 작은 스페이서
2x 고무 패드
2x 와셔 쌍
1x 나비 나사
1x 3-prong - 1/4" 어댑터
4x 미끄럼 방지 링
원 영문 설명
Insta360 Standard Motorcycle U-Bolt Mount
A more stable, reliable design for unbeatable onboard shots. Use with the Insta360 Action Invisible Selfie Stick to unlock incredible third-person shots of your ride - truly blockbuster potential.
Features:
Refreshed design with a new, patented gimbal structure gives unprecedented stability to your motorcycle shots.
All-new design, for a stabler onboard third-person shot.
Adaptable to most mainstream motorcycles.
Standard 1/4" adapter design, supports the Insta360 Action Invisible Selfie Stick.
GO 2 must be assembled with the Action Mount Adapter.
Specifications:
Weight: 201g
Dimensions: 96.5x51.5x57mm
Compatible with:
Ace Pro, Ace, X3, ONE RS (Twin/4K),GO 2, ONE X2, ONE R, ONE X
Notes:
Install the spacer inside the U-Bolt based on the clamping position and size.
Tighten the universal joint onto the U-Bolt securely before use.
The included washer pairs consist of two washer sets. Take care not to lose these during disassembly, as losing a washer may cause the nut to loosen under vibration.
U-Bolt can be installed onto the motorcycle frame, rear pedal bracket, bumper, and other secure areas. Always check the U-Bolt is locked into place, without rotation or play in the mount when secured.
Riding is only recommended on smooth roads at speeds not exceeding 80km/h (50mph). Off-road riding is not supported.
It is recommended to connect the Insta360 Action Invisible Selfie Stick with the 1/4" adapter on the Universal joint to ensure the stick is securely mounted. Please do not connect the selfie stick to the rest of the accessories. Please do not vigorously wrench the top of the selfie stick, as excessive torque may damage the Universal Joint.
When the motorcycle is parked outside for an extended period, remove accessories to keep them in the best condition.
Please use the accessory according to the installation method in this instruction manual, do not DIY. Damage caused by not following the instructions will not be covered by Insta360 warranty or replacement services.