DENALI DialDim 照明控制器 照明控制器

拨号暗照明控制器 - 通用贴合

突破性的 DialDim™ 照明控制器具有多色光晕调光开关，可让您从单个合并线束独立打开/关闭和调暗两组 3 线辅助灯。LED 光晕开关显示您的精确设置，并允许在飞行中轻松调光。蓝色光环控制灯组一，绿色光环控制灯组二;只需双击即可在两个电路之间切换。

该控制器还具有远光灯、转向信号灯和喇叭输入，可解锁智能闪光灯功能，这些功能可以通过转向灯取消辅助灯，将辅助灯闪烁为转向信号灯，或者在喇叭响起时闪烁灯光。

正在申请专利的多色光晕调光开关可以做的不仅仅是打开和关闭灯并调暗它们。对于初学者来说，它会显示两个灯的确切强度，因此您永远不会猜测您的灯是否打开，或者它们设置的强度。

得益于电子熔断电路，光环开关还可以显示并允许您选择每个电路的保险丝值。如果保险丝跳闸，LED 光晕将变为红色，提供实时反馈并允许重置保险丝。

最后但并非最不重要的一点是，开关光环兼作具有低压切断功能的电池监视器。我们业界首创的设计将在启动时闪烁不同的颜色，以显示您的电池健康状况，并在电池电压降至 10.8 伏以下时自动关闭辅助灯。

控制器外壳和开关均采用完全防水设计，每个接头处都有垫圈和 O 形圈，以确保在室外环境中轻松运行。 

特征：

• 开/关和调光 - 使用单个拨号暗™淡开关独立控制两组灯的开/关和强度级别。蓝色光晕控制灯组一，绿色光环控制灯组二。双击可在两个电路之间切换。
• 高/低同步 - 您的辅助灯将使用出厂远光灯开关在您选择的调光设置和全强度之间自动切换。只需将蓝色输入线连接到车辆的远光灯电路即可启用此功能。
• 隐身模式 - 开关上巧妙的 0% 调光设置可让您的灯在正常驾驶条件下“关闭”，但使用车辆的远光灯开关会跳到 100% 强度。在此模式下，灯也会对转向信号和喇叭输入做出反应，但在未检测到输入时将保持熄灭。
• 使用转向信号取消 - 启用后，主灯（蓝色电路 1）将与您的信号同步取消，以防止“冲刷”出厂转向灯。只需将黄色和橙色输入线连接到车辆转向信号电路即可启用此功能。
• 闪烁为转向信号灯 - 启用后，琥珀色能见度灯（绿色电路 2）将与出厂转向信号灯同步闪烁。只需将黄色和橙色输入线连接到车辆转向信号电路即可启用此功能。
• 带喇叭的频闪 - 启用后，当您吹响喇叭时，两个电路上的辅助灯将以 4Hz 频闪。只需将绿色输入线连接到车辆喇叭电路即可启用此功能。
• 电子熔断电路 - 两个光电路都是电子熔断的，可以直接从开关本身设置！光环将呈红色亮起，以在电路熔断时通知您。
• 电压显示指示灯 - 车辆启动时，开关光晕将闪烁绿色表示电池电压正常，或闪烁红色表示电池电压低于 11.8v。
• 低电压切断 - 如果电池电压降至 10.8v 以下，灯将无法通电，防止您陷入困境。开关光晕将闪烁 4 个红色 LED，以指示低电压情况。

规格：

• 两个完全独立的光电路 
• 每个电路有八个强度级别（5%、15%、30%、45%、60%、75%、100%）
• 八个电子保险丝值（1A、2A、4A、6A、8A、10A、15A、20A）
• 五条功能输入线（点火、远光灯、喇叭、左转、右转） 

内容：

• 1 x 拨号暗控制器™线束 
• 1 x 拨号调暗™多功能开关 
• 1 x 用于 22 mm 手柄的开关支架
• 4 x 168 cm 即插即用照明扩展  
• 1 x 通用输入触发线束 

DialDim Lighting Controller - Universal Fit

Ground-breaking DialDim™ Lighting Controller features a multicolor halo dimming switch that allows you to independently turn on/off and dim two sets of 3-Wire auxiliary lights from a single consolidated wiring harness. The LED halo switch displays your exact settings and allows for effortless dimming on the fly. The blue halo controls light set one and the green halo controls light set two; simply double click to switch between the two circuits.

The controller also features high beam, turn signal, and horn inputs to unlock intelligent flash features that can cancel your aux lights with your turn signal, flash your aux lights as a turn signal, or strobe your lights when you sound your horn.

The patent-pending multicolor halo dimmer switch can do a whole lot more than just turn your lights on and off and dim them. For starters, it displays the exact intensity of both of your lights so you're never stuck guessing if your lights are on, or what intensity they're set to.

Thanks to the electronically fused circuits, the halo switch can also display, and allow you to select, the fuse values for each circuit. And if a fuse trips, the LED halo will turn red providing real-time feedback and allow for resetting the fuse.

Last but not least, the switch halo doubles as a battery monitor with a low-voltage cutoff feature. Our industry-first design will flash different colors on startup to display your battery health and automatically shut off your auxiliary lights if the battery voltage drops below 10.8 volts.

The controller housing and switch both feature a fully waterproof design with gaskets and o-rings at every joint to ensure hassle-free operation in outdoor environments. 

Features:

• ON/OFF & Dim - Independently control two sets of lights on/off and intensity level using the single DialDim™ Switch. The blue halo controls light set one and the green halo controls light set two. Double click to switch between the two circuits.
• High/Low Sync - Your auxiliary lights will automatically switch between your selected dim setting to full intensity with the factory high beam switch. Simply connect the blue input wire to your vehicle's high beam circuit to enable this feature.
• Stealth Mode - A clever 0% dim setting on the switch allows your lights to be "off" during normal driving conditions but will jump to 100% intensity with your vehicle's high beam switch. The lights will also react to turn signal and horn inputs in this mode but will remain off when no inputs are detected.
• Cancel with Turn Signal - When enabled the main lights (blue circuit 1) will cancel in sync with your signal to prevent "washing out" your factory turn signal. Simply connect the yellow and orange input wires to your vehicle turn signal circuit to enable this feature.
• Flash as Turn Signal - When enabled your amber visibility lights (green circuit 2) will flash in sync with your factory turn signals. Simply connect the yellow and orange input wires to your vehicle turn signal circuit to enable this feature.
• Strobe with Horn - When enabled your auxiliary lights on both circuits will strobe at 4Hz when you sound your horn. Simply connect the green input wire to your vehicle horn circuit to enable this feature.
• Electronically Fused Circuits - Both light circuits are electronically fused and can be set right from the switch itself! The halo will illuminate red to notify you when a circuit fused is tripped.
• Voltage Display Indicator - Upon vehicle startup, the switch halo will flash green to indicate a healthy battery voltage, or flash red to indicate a battery voltage that is below 11.8v.
• Low Voltage Cutoff - If the battery voltage drops below 10.8v the lights will not power on preventing you from being stranded. The switch halo will flash 4 red LEDs to indicate the low voltage condition.

Specifications:

• Two fully independent light circuits 
• Eight intensity levels per circuit (5%, 15%, 30%, 45%, 60%, 75%, 100%)
• Eight electronic fuse values (1A, 2A, 4A, 6A, 8A, 10A, 15A, 20A)
• Five feature input wires (ignition, high beam, horn, left turn, right turn) 
• 20A max per circuit (30A max combined) 
• Operating voltage: 12 Volts

Contents:

• 1 x DialDim™ controller harness 
• 1 x DialDim™ multi-function switch 
• 1 x Switch mount for 22 mm handle bar
• 4 x 168 cm Plug-&-Play light extensions  
• 1 x Universal input trigger wire harness